This Project was to replace the aged exiting manual swing doors it involved the removal of the existing doors and shop front and the installation of a new aluminium and glass shop front with an ASN Erreka bi-parting system, finish polyester powder coated to a standard ral colour. The job was started at 10PM when the store closed and completed by 7AM when the store reopened causing no disruption to trade

These doors replaced the existing timber doors and frames with new aluminium doors and frames, the greenhouse was suffering from a lack of air circulation and  trouble accessing and exiting the building with plants and wheelbarrows. The old system with the timber doors was leaving the doors open. This solution was playing havoc with insects infestation. So we automated the aluminium doors on push pads and remote control fob system and replaced the glass of the inner door with fly mesh so allowing better air flow whilst keeping out the insects.

This Project required an Automatic sliding door with 24 hour 7 day access fully automatic system. It also had multiple activation options, these were radar motion detection 8 am to 5 pm Monday to Friday and Saturday AM, fob reader and video intercom 5 pm to 8 am Monday to Friday, Saturday PM and Sunday. It also required a remote controlled panic lockdown system and emergency opening. It also included electronic locking

This was a main entrance into a large high school. The entrance comprised two pairs of doors on an inner screen and two pairs of doors on an outer screen with a side screen to form a lobby. 3 of the 4 doors on each screen were manual on concealed hydraulic transom closers and one was automated with an ASN Erreka electronic door opener this allowed full compliance with the DDA regulations and Part M of the building regulations. All the outer doors were free access with the automatic operator being on motion radar activation. All the inner doors were on electronic locking to allow a secure lobby. The pair of manual doors were on a coded digital keypad system to allow entrance to allowed staff. The automatic swing door was on a key fob system again to allow entry by staff, there was a cctv system back to the reception desk with a dedicated monitor and audio intercom. The inner doors had the facility to be free access or secure entry at the discretion of the site

This was a new build rear car park entrance to a large medical center, the location and design was ideal for a pair of fully automatic swing door operators

This project was to automate a pair of existing aluminium doors on an existing shop front; this involves the reinforcing to the head of the door to an adequate strength to allow mounting of the automatic door equipment. This style of retro fit system can be used on most doors as long as they are in a good condition and have adequate head room to mount the equipment

This project was to automate a pair of existing aluminium doors on an existing shop front; this involves the reinforcing to the head of the door to an adequate strength to allow mounting of the automatic door equipment. This style of retro fit system can be used on most doors as long as they are in a good condition and have adequate head room to mount the equipment.

This was a new extension to an existing school where two aluminium and glass doors frames and screens were fitted and formed a lobby system with both the inner and outer doors being automated by ASN Erreka automatic swing door operators. The outer door was free access to allow users into a secure lobby out of the weather. The inner door had automatic electronic locking with coded digital key pad entry and audio intercom to the reception desk that also had a door release fitted.

ASN electric swing door opener mounted above an amour plate glass door with full top and bottom rails.

This was a new Lobby built on the rear entrance of a church to aid disabled access. It was a small lobby so comprising an inner and outer solid oak and glass door with solid oak and glass side panels. We fitted two ASN low energy door operators and the doors could easily be used manually as it was not exclusively for DDA (disabled discrimination act) use. But had 1 external and 1 internal large push pad remote controlled due to the age of the church wires could not be fitted. These buttons opened both doors simultaneously.

This was a new Lobby built on the rear entrance of a church to aid disabled access. It was a small lobby so comprising an inner and outer solid oak and glass door with solid oak and glass side panels. We fitted two ASN low energy door operators and the doors could easily be used manually as it was not exclusively for DDA (disabled discrimination act) use. But had 1 external and 1 internal large push pad remote controlled due to the age of the church wires could not be fitted. These buttons opened both doors simultaneously.

Existing timber doors in a day center require to be automated to comply with the DDA (disabled discrimination act) regulations and Part M of the building regulations. We fitted a pair of ASN Erreka fully automatic swing door operators with radar motion detectors inside and out and full on door safety sensors.

This project was part of a full shop refurbishment where we tasked with the removed the full existing timber shop frontage and replaced it with a new aluminium and glass shop front, this incorporating two pairs of fully automatic swing door operators, the doors required BS7036 health and safety regulation barriers due to a safety risk of side approach where the doors could collide with the users

This project was part of a full shop refurbishment where we tasked with the removed the full existing timber shop frontage and replaced it with a new aluminium and glass shop front, this incorporating two pairs of fully automatic swing door operators, the doors required BS7036 health and safety regulation barriers due to a safety risk of side approach where the doors could collide with the users

Tarmac head office main entrance, this project involved the removal of the existing screen and doors and the installation of a two door Aluminium and glass lobby door system, with an ASN Erreka electronic sliding door system on the inside and outside. Free access outside via motion detecting radar activation with a video entry system on the electronic locking inner ASN Erreka sliding door system   

This project was part of a full shop refurbishment where we tasked with the removed the full existing timber shop frontage and replaced it with a new aluminium and glass shop front, this incorporating two pairs of fully automatic swing door operators, the doors required BS7036 health and safety regulation barriers due to a safety risk of side approach where the doors could collide with the users

This project was part of a full shop refurbishment where we tasked with the removed the full existing timber shop frontage and replaced it with a new aluminium and glass shop front, this incorporating two pairs of fully automatic swing door operators, the doors required BS7036 health and safety regulation barriers due to a safety risk of side approach where the doors could collide with the users

This project was part of a full shop refurbishment where we tasked with the removed the full existing timber shop frontage and replaced it with a new aluminium and glass shop front, this incorporating two pairs of fully automatic swing door operators, the doors required BS7036 health and safety regulation barriers due to a safety risk of side approach where the doors could collide with the users

This was a main entrance to a large care home; it needed a large main electronic automatic door opener to allow for wheel chairs and electric buggies egress and access. The slave door also needed to be an emergency fire exit with a concealed panic bar system. This was a 24 hour 7 day door again on electronic locking; this was switched from fully automated to semi automatic (access control) by site staff with a remote control. The inner timber door pair was also automated on a low energy system to allow full access and egress into the main complex. The outer door required a BS7037 compliant barrier due to the issue of side approach

This was the main entrance to an office block in Manchester City Centre, where style and appearance is paramount. The system is built up in such a way that the automatic door equipment is literally bolted through pre-formed holes in the structural glass. We have installed a lot of this style in Manchester city center to offices, retail spaces and restaurants

This project was part of a full shop refurbishment where we tasked with the removed the full existing timber shop frontage and replaced it with a new aluminium and glass shop front, this incorporating two pairs of fully automatic swing door operators, the doors required BS7036 health and safety regulation barriers due to a safety risk of side approach where the doors could collide with the users

This was a new build and required a ASN Erreka single swing fully automatic door operating system on radar motion detectors. Also the slave door was required to be a fire exit so was installed with an emergency push bar system concealed in the aluminium frame work

This was a main entrance to a large care home; it needed a large main electronic automatic door opener to allow for wheel chairs and electric buggies egress and access. The slave door also needed to be an emergency fire exit with a concealed panic bar system. This was a 24 hour 7 day door again on electronic locking; this was switched from fully automated to semi automatic (access control) by site staff with a remote control. The inner timber door pair was also automated on a low energy system to allow full access and egress into the main complex. The outer door required a BS7037 compliant barrier due to the issue of side approach

This was a new build and required a ASN Erreka single swing fully automatic door operating system on radar motion detectors. Also the slave door was required to be a fire exit so was installed with an emergency push bar system concealed in the aluminium frame work

The under floor swing door operator is a great product if all conventional options are not possible, the direct drive motor gearbox is in a under floor mounting box with a cover plate and the electronics are mounted in a separate control cabinet inside the building. The main work is required prior to the door installation as there are extensive building works to be carried out prior to our attendance.

Tarmac head office main entrance, this project involved the removal of the existing screen and doors and the installation of a two door Aluminium and glass lobby door system, with an ASN Erreka electronic sliding door system on the inside and outside. Free access outside via motion detecting radar activation with a video entry system on the electronic locking inner ASN Erreka sliding door system 

This was a main entrance into a large high school. The entrance comprised two pairs of doors on an inner screen and two pairs of doors on an outer screen with a side screen to form a lobby. 3 of the 4 doors on each screen were manual on concealed hydraulic transom closers and one was automated with an ASN Erreka electronic door opener this allowed full compliance with the DDA regulations and Part M of the building regulations. All the outer doors were free access with the automatic operator being on motion radar activation. All the inner doors were on electronic locking to allow a secure lobby. The pair of manual doors were on a coded digital keypad system to allow entrance to allowed staff. The automatic swing door was on a key fob system again to allow entry by staff, there was a cctv system back to the reception desk with a dedicated monitor and audio intercom. The inner doors had the facility to be free access or secure entry at the discretion of the site

This project was to automate a pair of existing aluminium doors on an existing shop front; this involves the reinforcing to the head of the door to an adequate strength to allow mounting of the automatic door equipment. This style of retro fit system can be used on most doors as long as they are in a good condition and have adequate head room to mount the equipment.

This was a new extension to an existing school where two aluminium and glass doors frames and screens were fitted and formed a lobby system with both the inner and outer doors being automated by ASN Erreka automatic swing door operators. The outer door was free access to allow users into a secure lobby out of the weather. The inner door had automatic electronic locking with coded digital key pad entry and audio intercom to the reception desk that also had a door release fitted.

This was a new extension to an existing school where two aluminium and glass doors frames and screens were fitted and formed a lobby system with both the inner and outer doors being automated by ASN Erreka automatic swing door operators. The outer door was free access to allow users into a secure lobby out of the weather. The inner door had automatic electronic locking with coded digital key pad entry and audio intercom to the reception desk that also had a door release fitted.

This was a project where there was an open passage between the two parts of the school there was already doors into both building half way down the passage but the weather was becoming a big problem we installed a full aluminium and glass screen complete with a pair of ASN Erreka fully automatic door operators and to either side of that were two single emergency fire exit manual doors all had electronic locking that was linked into the fire alarm system. We installed one of these screens to both ends of the passage to fully enclose it. The result was a full covered passage way that was protected from the elements

This Project required an Automatic sliding door with 24 hour 7 day access fully automatic system. It also had multiple activation options, these were radar motion detection 8 am to 5 pm Monday to Friday and Saturday AM, fob reader and video intercom 5 pm to 8 am Monday to Friday, Saturday PM and Sunday. It also required a remote controlled panic lockdown system and emergency opening. It also included electronic locking

This was a project where there was an open passage between the two parts of the school there was already doors into both building half way down the passage but the weather was becoming a big problem we installed a full aluminium and glass screen complete with a pair of ASN Erreka fully automatic door operators and to either side of that were two single emergency fire exit manual doors all had electronic locking that was linked into the fire alarm system. We installed one of these screens to both ends of the passage to fully enclose it. The result was a full covered passage way that was protected from the elements

These doors replaced the existing timber doors and frames with new aluminium doors and frames, the greenhouse was suffering from a lack of air circulation and  trouble accessing and exiting the building with plants and wheelbarrows. The old system with the timber doors was leaving the doors open. This solution was playing havoc with insects infestation. So we automated the aluminium doors on push pads and remote control fob system and replaced the glass of the inner door with fly mesh so allowing better air flow whilst keeping out the insects.

This was a new extension to an existing school where two aluminium and glass doors frames and screens were fitted and formed a lobby system with both the inner and outer doors being automated by ASN Erreka automatic swing door operators. The outer door was free access to allow users into a secure lobby out of the weather. The inner door had automatic electronic locking with coded digital key pad entry and audio intercom to the reception desk that also had a door release fitted.

Church toilet door required automation to comply with the DDA (disabled discrimination act) and also to allow all parishioners full and free access. The ASN Erreka swing door unit was used to open and close the door this was interfaced to a dedicated toilet control system. This system controls the opening and closing of the door, the locking electronically of the door and also has a LED system to indicate if the toilet is vacant, occupied or locked, unlocked. The system is also designed to only allow locking when the door is closed so eliminates the button being pressed to lock down the system if the toilet is occupied

Church toilet door required automation to comply with the DDA (disabled discrimination act)  and also to allow all parishioners full and free access. The ASN Erreka swing door unit was used to open and close the door this was interfaced to a dedicated toilet control system. This system controls the opening and closing of the door, the locking electronically of the door  and also has a LED system to indicate if the toilet is vacant, occupied or locked, unlocked. The system is also designed to only allow locking when the door is closed so eliminates the button being pressed to lock down the system if the toilet is not occupied.

The existing door to the church toilet area had to be automated it required new hinges to allow full free movement, the ASN Erreka unit was ideal due to its silent running and noiseless movement.

Site had an existing lobby door system on manual door closers but had been audited for DDA (disabled discrimination act) compliance and failed on access to the building. So we attended site and automated the outer pair of doors on a ASN Erreka fully automatic swing door system and the inner set on a ASN Erreka low energy swing door operator system.

This project involved the removal of the existing 8000mm screen and the supplying and fitting of a new screen with a single automatic sliding door this was for the new hair and beauty salon. Due to the location and layout and volume of potential users we recommended that a safety pocket screen be fitted allowing maximum safety whilst opening  

This project was to help complete a DDA (disabled discrimination act) upgrade the building had gone through, they had had a new DDA (disabled discrimination act) lift fitted and we were to automate all the pass doors leading to the area. We did this with ASN Erreka swing door operates all fully automatic with full on door safety sensors. Some were on radar motion sensors, some on push pad activation and some on combination digital keypad entry with electronic locking.

This project was to help complete a DDA (disabled discrimination act) upgrade the building had gone through, they had had a new DDA (disabled discrimination act) lift fitted and we were to automate all the pass doors leading to the area. We did this with ASN Erreka swing door operates all fully automatic with full on door safety sensors. Some were on radar motion sensors, some on push pad activation and some on combination digital keypad entry with electronic locking.

This project was to help complete a DDA (disabled discrimination act) upgrade the building had gone through, we were to automate all the pass doors leading to the area. We did this with ASN Erreka swing door operates all fully automatic with full on door safety sensors some single and some double. Some were on radar motion sensors, some on push pad activation and some on combination digital keypad entry with electronic locking.

Single fold and Bi-folding doors are ideal when there is limited space for the install of a sliding door system or swing door system. The ASN fold comes in a package that is designed to fit into any hole complete with aluminium framework and doors.

The train station had very limited slide room and the room between the road side door and station side door was also too small to fit swing doors, this location was ideal for the ASN Automatic bi-fold door operating system.

The train station had very limited slide room and the room between the road side door and station side door was also too small to fit swing doors, this location was ideal for the ASN Automatic bi-fold door operating system.

This project was a medical center with two ASN sliding doors on the main entrance and to the car park an outer pair of ASN swing doors and a inner set of ASN Folding doors.

Folding doors were required because there was not enough space to have a sliding door, the distance between the outer swing doors and inner doors meant that if both were automated the sensors from both sets of doors would be seeing each other causing constantly ghosting (doors opening apparently with no one there) this made the small footprint of the folding door ideal

The train station had very limited slide room and the room between the road side door and station side door was also too small to fit swing doors, this location was ideal for the ASN Automatic bi-fold door operating system.

The train station had very limited slide room and the room between the road side door and station side door was also too small to fit swing doors, this location was ideal for the ASN Automatic bi-fold door operating system.

ASN Erreka bi parting sliding door at a flower store cold room with an oversize aluminium double glazed doors to help keep the cold in

This again required an ASN folding door due to size and space issues. The head room was also restrictive so installing a inline version was not possible. We therefore installed a surface applied version where the operating equipment is mounted inside the building above the lintel with the door opening into the door way. On this occasion we finished the exposed existing brickwork with polyester powder coated trims and flashings.

Folding doors were required because there was not enough space to have a sliding door, the distance between the outer swing doors and inner doors meant that if both were automated swing doors the sensors from both sets of doors would be seeing each other causing constant ghosting (doors opening apparently with no one there) this made the small footprint of the ASN folding door when in the open position ideal

This project was a medical center with two ASN sliding doors on the main entrance and to the car park an outer pair of ASN swing doors and a inner set of ASN Folding doors.

Folding doors were required because there was not enough space to have a sliding door, the distance between the outer swing doors and inner doors meant that if both were automated the sensors from both sets of doors would be seeing each other causing constantly ghosting (doors opening apparently with no one there) this made the small footprint of the folding door ideal

Folding doors were required because there was not enough space to have a sliding door, the distance between the outer swing doors and inner doors meant that if both were automated swing doors the sensors from both sets of doors would be seeing each other causing constant ghosting (doors opening apparently with no one there) this made the small footprint of the ASN folding door when in the open position ideal

Folding doors were required because there was not enough space to have a sliding door, the distance between the outer swing doors and inner doors meant that if both were automated swing doors the sensors from both sets of doors would be seeing each other causing constant ghosting (doors opening apparently with no one there) this made the small footprint of the ASN folding door when in the open position ideal

This again required an ASN folding door due to size and space issues. The head room was also restrictive so installing an inline version was not possible. We therefore installed a surface applied version where the operating equipment is mounted inside the building above the lintel with the door opening into the door way. On this occasion we finished the exposed existing brickwork with polyester powder coated aluminium trims and flashings. The door also had a electronic motor lock and audio access control, staff access was by fob reading system.

This again required an ASN folding door due to size and space issues. The head room was also restrictive so installing an inline version was not possible. We therefore installed a surface applied version where the operating equipment is mounted inside the building above the lintel with the door opening into the door way. On this occasion we finished the exposed existing brickwork with polyester powder coated aluminium trims and flashings. The door also had a electronic motor lock and audio access control, staff access was by fob reading system.

This project involved the removal of the existing 8000mm screen and the supply and installation of a new screen with a single automatic sliding door. This was for the new hair and beauty salon. Due to the location and layout and volume of potential users, we recommended that a safety pocket screen be fitted allowing maximum safety whilst opening

Folding doors were required because there was not enough space to have a sliding door, the distance between the outer swing doors and inner doors meant that if both were automated swing doors the sensors from both sets of doors would be seeing each other causing constant ghosting (doors opening apparently with no one there) this made the small footprint of the ASN folding door when in the open position ideal

This Project was an existing industrial unit that a large wholesale company had taken over, they required an automatic sliding door system that would work in conjunction with the existing security door but was also weather tight, not allowing the wind and rain in. We formed a “U” shaped lobby from standard aluminium and glass shop front sections and put a roof on that closed the gap between the existing Roller shutter door, we then fitted some industrial brush strip seal sections thus allowing the Roller shutter door to still go up and down but retain a weather seal and security

This Project was an existing industrial unit that a large wholesale company had taken over, they required an automatic sliding door system that would work in conjunction with the existing security door but was also weather tight, not allowing the wind and rain in. We formed a “U” shaped lobby from standard aluminium and glass shop front sections and put a roof on that closed the gap between the existing Roller shutter door, we then fitted some industrial brush strip seal sections thus allowing the Roller shutter door to still go up and down but retain a weather seal and security

This Project was an existing industrial unit that a large wholesale company had taken over, they required an automatic sliding door system that would work in conjunction with the existing security door but was also weather tight, not allowing the wind and rain in. We formed a “U” shaped lobby from standard aluminium and glass shop front sections and put a roof on that closed the gap between the existing Roller shutter door, we then fitted some industrial brush strip seal sections thus allowing the Roller shutter door to still go up and down but retain a weather seal and security

This again was the main entrance to an office block in Manchester City Centre, where style and appearance are paramount. The system is built up in such a way that the automatic door equipment is literally bolted through pre-formed holes in the structural glass. This was a unmanned entrance so was always on access control         

This is another main entrance to an office block in Manchester City Centre, where style and appearance is paramount. We have done a lot of this style in Manchester city center to offices, retail spaces and restaurants. With different levels of security and activation 

This project involved the removal of the existing Timber doors and screen and the supplying and fitting of a new screen with an ASN Erreka single automatic sliding door system. Due to the location and layout, volume and type of users we recommended that a safety pocket screen be fitted allowing maximum safety whilst the door was opening. This project was completed in a day causing minimal disruption. It was part of a 5 site project across the north of

This was the main entrance to a restaurant in Manchester City Centre, where yes style and appearance is paramount. The system is built up in such a way that the automatic door equipment is literally bolted through pre-formed holes in the structural glass.

This is the main entrance to a restaurant in Manchester City Centre, where style and appearance is paramount. We have installed a lot of this style in Manchester city center to offices, retail spaces and restaurants.

No matter how well the equipment has been designed, manufactured, installed, commissioned and maintained the possibility for failure cannot be ignored.

All automatic doors have to be serviced every 6 months to meet the BS7036 British standards Health and safety requirements; we will service and repair any make of equipment.

This project involved the removal of the existing Timber doors and screen and the supplying and fitting of a new screen with an ASN Erreka single automatic sliding door system. Due to the location and layout, volume and type of users we recommended that a safety pocket screen be fitted allowing maximum safety whilst the door was opening. This project was completed in a day causing minimal disruption. It was part of a 5 site project across the north of

This project involved the removal of the existing Timber doors and screen and the supplying and fitting of a new screen with an ASN Erreka single automatic sliding door system. Due to the location and layout, volume and type of users we recommended that a safety pocket screen be fitted allowing maximum safety whilst the door was opening. This project was completed in a day causing minimal disruption. It was part of a 5 site project across the north of

This project involved the removal of the existing Timber doors and screen and the supplying and fitting of a new screen with an ASN Erreka single automatic sliding door system. Due to the location and layout, volume and type of users we recommended that a safety pocket screen be fitted allowing maximum safety whilst the door was opening. This project was completed in a day causing minimal disruption. It was part of a 5 site project across the north of

This project was to remove the existing timber and glass shop front to an independent pharmacy and replace it with a new aluminium and glass shop front that incorporated an ASN Erreka Automatic Bi parting door.

This project was to remove the existing timber and glass shop front to an independent pharmacy and replace it with a new aluminium and glass shop front that incorporated an ASN Erreka Automatic Bi parting door.

This was a complete shop refurbishment and we were asked to provide all glass sliding doors, the system comprises an ASN Erreka electronic sliding door operator and ASN Erreka Glass clamps, these connect the 12mm armour plate glass sheets to the operator, this system had the addition of manual locks on the bottom corners only

This was again to remove the existing timber swing doors to a public library and the installation of 2 screens each with a single slide ASN Erreka door forming a lobby, each door was offset to minimize the effects of the weather.

This project involved the removal of the existing Aluminium swing doors to a public library and the installation of an ASN Erreka sliding door system. Site were adamant that they needed a sliding door to maximize the internal floor space. This required the addition of a safety pocket door thus allowing the sliding door to slide across the brick pillar allowing us to maximize the opening. The addition of an electric roller shutter added much needed security to the building.

This involved the installation of 2 number ASN Erreka bi parting sliding doors at a flower store cold room with aluminium double glazed doors to help keep the cold in. The system was one entrance doors and one exit door; these doors had to be over height to allow access of the trolleys with tall flowers

This project was to the main entrance of a large high school that required an aluminium and glass lobby system with inner and outer ASN Erreka automatic sliding doors, again due to the location, volume of traffic and age of users we again strongly recommended safety pocket doors

This project was to the main entrance of a large high school that required an aluminium and glass lobby system with inner and outer ASN Erreka automatic sliding doors, again due to the location, volume of traffic and nature of the users we again strongly recommended safety pocket doors be fitted for maximum  protection during the opening cycle